PSRE Co., the leading developer of smart simulation and sizing tools for every piping and equipment engineer/designer, is pleased to announce the expansion of its market presence for the PASS Software Suite in the Middle East and North Africa . PSRE has signed a distribution agreement with Adams Consultancy & Infrastructure (Adams C&I).
Read more...
|
Start-Prof version 4.83 R3 release. Changes:
- Added automatic static seismic analysis for all ASME, DLT, GB, and EN codes
- Fixed problem with UNDO function, that sometimes corrupted the model (happened in 4.83 R2)
- Fixed problems with submerged buried pipeline
- Fixed problem with calculation of maximum loads from all operation modes in support local coordinates
- Fixed problem with inserting nodes into bends and curved pipes
- Increased the friction factor range up to 0.75 to model highly corroded piping
- Fixed other minor bugs (freezes, crashes, unknown errors)
The Start-Prof users with valid warranty may download the new version from downloads page. To upgrade the current version the dongle updating is not needed.
Read more…
|
New version released Nozzle-FEM 2.16 that significantly expands the capabilities of previous versions:
- new shell type has been added - rectangle plate;
- calculation of thermal strains has been added, which allowed to analyze additional stresses arising from constrained temperature strains or action of different temperatures in the components;
- strength verification tests has been updated and revised for ASME BPVC.VIII.1-2017 and ASME BPVC.VIII.2-2017, EN 13445-3:2014 (E) Issue 4 (2017-07), GOST 342233.1-2017 (verification test has been added for materials that work at temperatures in the range where creep and stress rupture govern the selection of stresses);
- etc.
Read more...
All users under technical support are recommended to install this program version.
|
Start-Prof version 4.83 R2 release. Changes:
- Improved import from Caesar II function. Now it can convert nozzles created using CNODE, reducers, rigid elements, code, insulation weight, and more other improvements
- Added function, allows to replace the valve into rigid element. It can be used to improve the model after importing from Caesar II
- GB/T 20801-2006: added calculation of the stresses in test mode
- ASME B31.1: Code updated to B31.1-2018
- ASME B31J-2017: added Errata to B31J-2017 from 11-9-2017
- Seismic code SP 14.13330.2014 is replaced by SP 14.13330.2018
- Improved the method of slip joint modeling. Now guide support near the slip joint is not necessary
- Improved the splitting pipe element dialog. Added ability to insert any support from any node and other improvements
- Added ability to see transparent piping model
- Added ability to see SIF and k-factors right in the bend, tee and reducer properties window
- Added ability to place the supports in tees: sliding, springs, rigid hanger, nonstandard restraint
- Fixed other minor bugs
The Start-Prof users with valid warranty may download the new version from downloads page. To upgrade the current version the dongle updating is not needed.
Read more…
|
The new version 4.1 of PASS/HYDROSYSTEM has released in October 2018. This new version contains two big improvements, which are expected to considerably extend the applicability of this versatile simulation and sizing solution helping users to efficiently design complex piping systems that meet all requirements while minimizing design and operational cost.
To get more details…
|
Version 3.0 includes a number of additional calculations, corrections and options.
- Implemented codes GOST 34233.1-2017 ... GOST 34233.12-2017, issued in place of GOST R 52857.1-2007 ... GOST R 52857.12-2007, GOST R 51273-99, GOST R 51274-99;
- The calculation of seismic and wind loads according to GOST 34283-2017 is implemented;
- Added new elements: "Vessel Assembly", "Rigid link", allowing to count simultaneously several connected devices;
- Added nozzle for the air cooler chamber (including junctions with the side walls of the welded chambers);
- And others...
To get more details…
All users under aftersales service are recommended to install this program version.
|
PSRE Co NTP Truboprovod will take part in ASME PVP 2018 conference – World Forum and Leading Show for Pressure Vessels & Piping 2018 in Prague, Czech Republic. Waiting you at our booth 14 of the PVP 2018 Exhibition 16-18 July to discuss how we can help you by our software and service!
|
START-Prof version 4.82 R4 release. Changes:
- Fixed some problems with import from Caesar II
- Fixed some other bugs
The Start-Prof users with valid warranty may download the new version from downloads page. To upgrade the current version the dongle updating is not needed.
|
PASSAT new version 2.14 is released, which includes a number of additional calculations, corrections and options.
- Calculation of thermal insulation using calculation module of the "Insulation" program developed by NTP Truboprovod;
- Calculation of dished head, cylindrical shells and conical transitions with fixing nodes as per ASME VIII-1, div.II;
- Calculation of reverse flanges as per ASME VIII, div.I;
- Calculation of seismic stability as per AzDTN 2.3-1 (Azerbaijan);
- And others...
To get more details…
All users under aftersales service are recommended to install this program version.
|
Changes:
- Fitting Database: Fixed insertion of equal tees
- Start-Elements: Fixed error for buried pipes
- Fixed some problems in project tree
- DL/T 5366-2014: Fixed displacements from pressure loads in cold state and installation
- state
- Fixed some other bugs
The Start-Prof users with valid warranty may download the new version from Downloads page. To upgrade the current version the dongle updating is not needed.Downloads. To upgrade the current version the dongle updating is not needed.
|